Search found 187 matches
- Mon Jul 17, 2023 7:31 pm
- Forum: Technical Discussions
- Topic: IGNITION TIMING. HOW TO WITH STROBE LIGHT.
- Replies: 6
- Views: 2573
Re: IGNITION TIMING. HOW TO WITH STROBE LIGHT.
Hi, no answer yet, so I try to answer. TDC or 3/4 market is for the adjustment of the timing chain/camshafts towards crankshaft. For the ignition you need to use the 10degrees marker - at idle you should have 10 degrees advance ignition. In my experience with modern petrol a bit less sometimes work ...
- Sun Jul 02, 2023 1:07 pm
- Forum: Market
- Topic: WTB - Rear chrome tail light trim
- Replies: 2
- Views: 451
Re: WTB - Rear chrome tail light trim
Hi,
I don’t have a spare set - but these are in total 6 pieces, the bows are separate items. When I remember correct Dinoparts has reproduced them but they are not really cheap…
I don’t have a spare set - but these are in total 6 pieces, the bows are separate items. When I remember correct Dinoparts has reproduced them but they are not really cheap…
- Mon May 15, 2023 6:45 am
- Forum: Technical Discussions
- Topic: Chain tensioner leaking
- Replies: 7
- Views: 2881
Re: Chain tensioner leaking
I have no idea how it works to keep the inner part in place and to get it back in into the outer part with heads on, as I have it done always when the heads are taken apart but would be interesting to hear if/how it works.
- Sun May 14, 2023 4:30 pm
- Forum: Technical Discussions
- Topic: Chain tensioner leaking
- Replies: 7
- Views: 2881
Re: Chain tensioner leaking
The end with the gear can’t be dragged out to the outside of the head and can/will fall into the engine when you remove the outer part.
- Wed May 10, 2023 7:45 am
- Forum: Technical Discussions
- Topic: Clutch mega problem, need expertise.
- Replies: 5
- Views: 2281
Re: Clutch mega problem, need expertise.
You don’t have to cut the pins they are pressed in and can be pressed out. When I remember it right, I have taken out these pins when I renewed my clutch as the 6 screws are holding it on the flywheel.
- Thu May 04, 2023 8:13 am
- Forum: Technical Discussions
- Topic: Chain tensioner leaking
- Replies: 7
- Views: 2881
Re: Chain tensioner leaking
There are two seals: - one paper seal between head and tensioner - an O-Ring under the tensioner cap. While you can unscrew the cap and then see and can exchange the o-ring, the paper seal can only be replaced when the head is disassembled. There is another thing: you still have the old version of t...
- Fri Apr 14, 2023 10:53 pm
- Forum: Technical Discussions
- Topic: 2400 Coupe engine rebuild
- Replies: 42
- Views: 15136
Re: 2400 Coupe engine rebuild
Hi Richard, calve clearances are be defined in the Fiat manuals on 0,2 inlet and 0,4 on outlet as in the Ferrari specs it’s ( for the same engine!) 0,15 and 0,30. So I go for the 0,2 and 0,4 but in cases like you describe go for the closer by and lower alternative. But in your example if to choose b...
- Wed Apr 05, 2023 9:28 pm
- Forum: Technical Discussions
- Topic: 2400 Coupe engine rebuild
- Replies: 42
- Views: 15136
Re: 2400 Coupe engine rebuild
Right, you need these inner spanners with the "plates" and then to Place them as much up and down as possible - then it works very well.
- Fri Mar 10, 2023 11:50 pm
- Forum: Market
- Topic: Wanted: lower windscreen chromes
- Replies: 4
- Views: 3810
Re: Wanted: lower windscreen chromes
Coupé? Spider?
- Tue Mar 07, 2023 9:59 pm
- Forum: The Fiat Dino
- Topic: Looking for a German Fiat ID tag
- Replies: 7
- Views: 3651