New member introduction

Discussions and Socializing

Moderators: Philt68, doublegarage

Re: New member introduction

Postby HugoHarris » Thu Aug 03, 2017 4:37 pm

Tim, on the subject of switch bezels, there are a couple of suppliers purporting to sell replacement chrome bezels for Dinos, but I don't know whether they are correct for the 2.4 Spider:

http://www.autostoria.fr/en/indicators/ ... dino-.html

http://www.midwest-bayless.com/p-10243- ... e-nos.aspx
2400 Spider #1364
HugoHarris
 
Posts: 86
Joined: Wed Mar 12, 2014 4:07 pm
Location: UK
Dino: Fiat Dino 2.4 Spider

Re: New member introduction

Postby Scalino » Sat Aug 05, 2017 12:29 pm

Hi Hugo, thanks I know of those. Unfortunately those are not correct for a Spider as the edges are rounded of. They are the same as the 124 Spider and others use.
Scalino
 
Posts: 37
Joined: Mon Jul 24, 2017 7:22 pm
Location: The Netherlands
Dino: Fiat Dino 2.4 Spider

Re: New member introduction

Postby Scalino » Mon Oct 23, 2017 8:15 pm

Bit of an update;

We got the carbs all rebuilt, but are now dealing with a severe fuel leak coming from the middle carb (more detail in the technical section of the forum). We did get the carbs to look great though :lol: . Also had a new throttle shaft (running along the firewall) made and installed new bushes.

They went from looking like this:

Image

Via:

Image

Image

Image

To this:

Image

Image

Image

Image

So at least it looks good while I'm frustrated with it...
Scalino
 
Posts: 37
Joined: Mon Jul 24, 2017 7:22 pm
Location: The Netherlands
Dino: Fiat Dino 2.4 Spider

Re: New member introduction

Postby HugoHarris » Tue Oct 24, 2017 5:47 pm

Wow! Beautiful carbs!
2400 Spider #1364
HugoHarris
 
Posts: 86
Joined: Wed Mar 12, 2014 4:07 pm
Location: UK
Dino: Fiat Dino 2.4 Spider

Re: New member introduction

Postby Scalino » Tue Oct 24, 2017 6:49 pm

Thanks Hugo! If only they would work correctly...

I forgot to mention that before the middle carburator decided it didn't like having fuel in it, the alternator caught fire due to the chain tensioner leaking. So we had that rebuild and installed the drip that's available from DinoParts. Yep, it hasn't really been smooth sailing so far.

We were also able to buy some parts; a pair of horns with a compressor (correct tipo 2000) - among other things - from @Alfredino and a choke cable mounting bracket for on the air filter housing from @Georg. Both were excellent to deal with and all the parts arrived safely :)

The bracket will go on when the carb problem is solved and we mount the air filter again. The horns will need a restoration, which isn't a priority at the moment obviously.
Last edited by Scalino on Wed Jan 03, 2018 4:41 pm, edited 1 time in total.
Scalino
 
Posts: 37
Joined: Mon Jul 24, 2017 7:22 pm
Location: The Netherlands
Dino: Fiat Dino 2.4 Spider

Re: New member introduction

Postby Scalino » Wed Jan 03, 2018 4:41 pm

So, a small update. Unfortunately, yet more issues. We’ve had the lead plugs replaced (Bart did an excellent job; https://nl-nl.facebook.com/Nose2TailCCE/). While the carbs were there Bart asked whether we would like them wet blasted, since he was going there anyway. Well, we couldn’t say no to that. They really look like new (in- and outside), maybe even better than new. Bart also skimmed them, as often the ‘ears’ of the carbs are bent due to overtightening (which was the case), which can cause false air to enter.

With that all done, we put them back together. We were all ready to put them back on the car, only to find a quite severe coolant leak. It turns out the pipe running under the carburetors to the heater is cracked on the underside. We noticed coolant when removing the carbs, thought it could be either a spill (unlikely) or and old leak (possible, since the thermostat housing was replaced, without taking the carbs of). We cleaned it up, forgot about it and then some swearing occurred when we wanted to install the carburetors.
The conclusion is we have to replace the pipe. Fortunately, both Dinoparts and Superformance sell them. However, Dinoparts asks nearly two hundred euros for the one needed and Superformance currently doesn’t have them available. We will pull the line when we have the time and see whether we either make it ourselves or have it remade, because I simply refuse to pay two hundred euros for a – quite simple – coolant pipe. Maybe I’m being optimistic about the R&D/manufacturing costs, but two hundred euros?! Sorry, bit of frustration ;)

While looking at how we are going to remove the line, we noticed the radiator drain is above the chassis beam and electrical wires. Who the hell designed that? Or the location isn’t original, but I think it is the original radiator, just with a new core.

I’ll update when we have the line of, hopefully this weekend. I had planned to do some work on my Alfa, but alas I want this done first. It has taken way too much time already.

At least the carbs look even better now!
Attachments
IMG_5169.JPG
IMG_5158.JPG
IMG_5138.JPG
IMG_5135.JPG
IMG_5132.JPG
Scalino
 
Posts: 37
Joined: Mon Jul 24, 2017 7:22 pm
Location: The Netherlands
Dino: Fiat Dino 2.4 Spider

Re: New member introduction

Postby Luis A » Wed Jan 03, 2018 10:14 pm

Those carbs look gorgeous! Hopefully you can find a reasonable alternative to the pricey pipe.
Luis A
 
Posts: 22
Joined: Tue Oct 31, 2017 12:35 am
Dino: No Dino (yet)

Previous

Return to The Garage

Who is online

Users browsing this forum: No registered users and 1 guest